CART
Total
€ 0,00
Shipping costs and promotions, calculated at checkout.

De Rosa 70 titanium rear thru axle Grade 5 Ti-6Al-4V titanium

De Rosa 70 titanium rear thru axle
Technical Specifications:

Material: Titanium Grade 5- Ti6Al4V
Total Axle Length: 164 mm
Under-head Lenght: 158 mm
Axle Diameter: 12 mm
Thread: M12x1,5
Thread Length: 17 mm
Allen key seat: 6 mm hexagon


For a perfect fit: check length, thread size, pitch and shoulder against your original thru-axle before purchasing.
Code: MEPP12DRO070164
€ 140,00
DescriptionReviewsQuestionsVideo

Titanium rear thru axle for De Rosa 70

Turned in Italy from certified Grade 5 Ti-6Al-4V titanium bar.

What changes on the bike

You chose your frame and wheels with care. Give the same care to what joins them.

In corners, under braking and when you get out of the saddle, the connection between wheel and bike works under load. With the same shape, a certified Grade 5 Ti-6Al-4V titanium axle flexes about a third less than one in 7075 aluminium, right where you want a bike that stays composed in corners, steady under braking and direct under power.

More stiffness in the axle, high fatigue strength and machining finished down to the thread. For riders who want a bike looked after even in the details you see least.

Cyclist leaning into a mountain road corner

The axle is small. The forces aren't.

Front: cornering

In a corner your weight adds to the force pushing you outwards, and the load passes from the wheel to the point where it joins the bike. Hit a bump mid-corner and the knock pushes the wheel sideways, with the wheel acting as a lever: where it's fixed, even a small push gets multiplied.

The same corner seen from the axle: diagram of the forces with the bike leaning at 38 degrees

Front: braking

Under braking the load climbs further, because the disc caliper sits on one side only and levers right there. The axle helps keep the wheel where you put it: in titanium, with the same shape, it gives less than an aluminium one, just when you want a clean line and a composed front end.

The forces on the front thru axle when cornering and braking

Rear: out of the saddle

In a hard effort out of the saddle, the chain pulls the hub from one side only, with a force that can reach twice your body weight. And the pull rises and falls with every pedal stroke, about ten thousand times an hour. Meanwhile the bike rocks beneath you and the wheel follows. The axle helps hold the wheel steady: in titanium, with the same shape, it gives less than an aluminium one just as you push, and Grade 5 titanium is an alloy with high resistance to repeated loads.

Top view of the rear axle: the chain pulls the hub from one side

More than grams, performance.

Cyclists weigh everything. But a few grams on an axle weigh about as much as a sip from your bottle, and they make almost no difference to the time on a climb. On a descent, seconds are won through control: when the front end gives you confidence, you brake later, commit to the corner and carry more speed. The scales can't measure that.

Why certified Grade 5 Ti-6Al-4V titanium

The difference starts with the material: ours are made only from Grade 5 Ti-6Al-4V titanium bar certified to AMS 4928. If an axle doesn't state the grade and has no certificate, you don't know what titanium you're fitting.

Compared with Grade 2 titanium: Grade 2 is almost pure titanium and costs less, but it has about half the strength of Grade 5: normally less than 7075 aluminium too.

Compared with 7075 aluminium: with the same shape it flexes about a third less, and its tensile strength is far higher.

Repeated loads and corrosion: Grade 5 is an alloy with high fatigue strength, and sweat, road salt and washing are not a problem. No anodising to wear off: the protection is the material itself.

Why not all titanium is the same
Same load: the Grade 5 titanium axle flexes a third less than the 7075 aluminium one, and is stronger than Grade 2 titanium

Turned in Italy

Our thru axles aren't assembled from other people's parts: we turn them ourselves at Rodolfo Giani sas, just outside Milan, from certified Grade 5 Ti-6Al-4V titanium bar. Road, gravel and MTB.

They don't come off a production line: we make them in small batches, pick them up one at a time and brush grease onto the thread. It's one more check, done with care and attention to detail.

If your size isn't listed, ask us for a custom axle for your fork or frame.

Brush spreading grease on the thread of a titanium thru axle

Estimated values, not measurements. Front: road bike, 85 kg rider and bike, 38° lean at constant speed, 0.5 g braking on the front brake only, 160 mm disc, 700×28 wheel. Rear: 100 kg on the pedal, 52T chainring, 172.5 mm crank, 80 kg rider, 90 rpm. Loads in kilograms-force, at the connection between hub and frame or fork. Compared with 7075-T6 aluminium of the same shape. Grade 2 titanium: from 345 MPa (ASTM B348 minimum) to 485 MPa (typical). Cyclist image generated with AI.

14-day return policy. Contact us and we will explain how to proceed.
We ship worldwide. (Terms and conditions apply, find out more)
Pay with complete peace of mind thanks to our secure connection and wide range of payment methods.
Products can be customized only where indicated.